Nexillumi L Shape 4-pin Connectors Angle Adjustable(90-180 Degrees) LED Strip Connectors for 10mm Width 5050 RGB LED Strip Lights(10 Pcs)

Works great lakes corners a breeze

Although it took me about three tries to get a really good connection, once I got the first one done, the rest have been quite easy. Makes a reliable connection and perfect square angles.

These splicers work well. I used seven of them on the octopus. I recommend leaving about an inch of your light strip not taped to allow for any flexing or relaxing of the joint. The connections are tiny and any movement may pull them apart. Not knowing this beforehand I ended up using tape across the tops of the splicers to hold them in position. All and all, I really love how it looks!

I had a really hard time installing these even after reading the instructions. The connections were very loose on my 5050 LED strip that I pre-cut to fit the rear edges of my 65" TV. After 20 minutes of trying and only getting barely flickering LED strips, I was ready to give up, put them back in the bag, and return them. Luckily my wife had more patience than I did and figured out a way to wiggle them back and forth as they were being put in and managed to get them in far enough to work. After using our own 3M tape to ensure they stayed in place, they work.Side Note: the picture shows it's "ability" to straighten out when needed. Unfortunately this is not the case for me, I tried straightening them out they way the picture showed and they failed to match the capability advertised without feeling like I was going to pull the leads out of the wires. Didn't affect my use of them the way I needed them, just a side note for those that think it's flexible to do that...do so at your own risk.

I have bought the Nexillumi 65ft long set for my living room and just now the 50 ft set for my kitchen. I am having them inset into cubbies so I needed extra 45 degree connectors. I bought this pack of ten but might need one more. The quality of these pieces is much better than expected. As you can see in my pictures heavy wire, heavy plastic, and solid connectors inside. These products have come a long way in the past years and it helps to buy good stuff from the beginning also :) ...... Ill be posting videos of the lights up working soon if you check out my other reviews....God Bless, Richard W.

I used these for workstation lighting. They have EXTREMELY poor connections. First thing is you need to strip the tape and glue off the LED strips for it to fit properly. That's not the fault of the connector, that's just what it is. Doing that made it fit very easy, however the clips dont snap closed which allows the strips to wiggle inside the connections. At one point I had one part of the strip lit up in light green and the next piece attached with the connector was red because the only connection it was getting was from the power and red connections. Wiggling the connection just made it bounce from on to off, to all different shades of colors. I spent more time fooling around with these stupid connectors trying to make them work than I did actually installing the lights because I had to keep installing the strip, cutting the strip to get a new fresh end, etc.. I will probably replace these with some other 90 degree connections just to ensure I have a solid connection, but right now my fingers still hurt from trying to get these things to snap closed. Very disappointing.

The only issue is you MUST cut the led tape very precisely. If you do not cut it exactly as directed they will not work. I found cutting the led tape connector just a fraction shy of the instructions worked best. Once connected be careful not to stress the connection or it can move and not work. Make sure the led tape is cut in a straight line across....do not be in a rush...take your time to do it right and youll be fine. If youre in a hurry wait until you have time. I did 7 90 degree angles but it took about 15mins to figure out how critical the cuts must be to work. Once the correct cut and inserts are all under the tabs they work as advertised.

The #1 thing to get this to work right is the cut on the LED strip. If you don't cut your strip correctly, its not going to work properly. Alot of people will put the blame on the connectors when in realty its the cut on their strip. Ordering more as I am going to need quite a few to complete my project.

products dont have size , pore infomation